CCNA 1 Final Exam R&S v5 Exam Answers Introd to Networks

By | November 10, 2013

CCNA 1 Final Exam R&S v5 Exam Answers Introd to Networks 2014
CISCO CCNA Questions and Answers v5 Quiz TEST (Version 5.0) Final Exam
This exam will cover material for all chapters in CCNA R&S Introduction to Networks curriculum.

1
p1[1]
Refer to the exhibit.
The network administrator enters these commands into the R1 router:
R1# copy running-config tftp

Address or name of remote host [ ]?
When the router prompts for an address or remote host name, what IP address should the administrator enter at the prompt?
192.168.9.254
192.168.10.1
192.168.10.2
192.168.11.254
192.168.11.252

2 Which three statements characterize the transport layer protocols? (Choose three.)
TCP uses port numbers to provide reliable transportation of IP packets.
TCP and UDP port numbers are used by application layer protocols.
TCP uses windowing and sequencing to provide reliable transfer of data.
TCP is a connection-oriented protocol. UDP is a connectionless protocol.

UDP uses windowing and acknowledgments for reliable transfer of data.

3 What is the purpose of ICMP messages?
to inform routers about network topology changes
to ensure the delivery of an IP packet
to monitor the process of a domain name to IP address resolution
to provide feedback of IP packet transmissions

4 A technician uses the ping 127.0.0.1 command. What is the technician testing?
connectivity between a PC and the default gateway
connectivity between two adjacent Cisco devices
physical connectivity of a particular PC and the network
the TCP/IP stack on a network host
connectivity between two PCs on the same network

5 What will a Layer 2 switch do when the destination MAC address of a received frame is not in the MAC table?
It notifies the sending host that the frame cannot be delivered.
It initiates an ARP request.
It forwards the frame out of all ports except for the port at which the frame was received.
It broadcasts the frame out of all ports on the switch.

6 What is a characteristic of the LLC sublayer?
It places information in the frame that allows multiple Layer 3 protocols to use the same network interface and media.
It provides delimitation of data according to the physical signaling requirements of the medium.
It defines software processes that provide services to the physical layer.
It provides the logical addressing required that identifies the device.

7
On which switch interface would an administrator configure an IP address so that the switch can be managed remotely?
VLAN 1
console 0
vty 0
FastEthernet0/1

8
A network engineer is measuring the transfer of bits across the company backbone for a mission critical database application. The engineer notices that the network throughput appears lower than the bandwidth expected. Which three factors could influence the differences in throughput? (Choose three.)
the reliability of the gigabit Ethernet infrastructure of the backbone
the amount of traffic that is currently crossing the network
the type of traffic that is crossing the network
the sophistication of the encapsulation method applied to the data
the bandwidth of the WAN connection to the Internet
the latency that is created by the number of network devices that the data is crossing

9
When applied to a router, which command would help mitigate brute-force password attacks against the router?
service password-encryption
login block-for 60 attempts 5 within 60
banner motd $Max failed logins = 5$
exec-timeout 30

10
Which two statements correctly describe a router memory type and its contents? (Choose two.)
ROM is nonvolatile and contains basic diagnostic software.
FLASH is nonvolatile and contains a limited portion of the IOS​.
ROM is nonvolatile and stores the running IOS.
RAM is volatile and stores the IP routing table.
NVRAM is nonvolatile and stores other system files.

11
Which two components are necessary for a wireless client to be installed on a WLAN? (Choose two.)
custom adapter
wireless bridge
media
wireless NIC
crossover cable
wireless client software

12 Launch PT – Hide and Save PT
p1211[1]
Open the PT activity. Perform the tasks in the activity instructions and then fill in the blank.
The Server0 message is winner

13
A host is accessing a Web server on a remote network. Which three functions are performed by intermediary network devices during this conversation? (Choose three.)
applying security settings to control the flow of data
notifying other devices when errors occur
regenerating data signals
acting as a client or a server
serving as the source or destination of the messages
providing a channel over which messages travel

14
Clipboard015[1]

15
Clipboard011[1]

16
Which address on a PC does not change, even if the PC is moved to a different network?
IP address
logical address
MAC address
default gateway address

17
What will happen if the default gateway address is incorrectly configured on a host?
A ping from the host to 127.0.0.1 would not be successful.
The host will have to use ARP to determine the correct address of the default gateway.
The host cannot communicate with other hosts in the local network.
The host cannot communicate with hosts in other networks.
The switch will not forward packets initiated by the host.

18
A host PC has just booted and is attempting to lease an address through DHCP. Which two messages will the client typically broadcast on the network? (Choose two.)
DHCPREQUEST
DHCPOFFER
DHCPDISCOVER
DHCPNACK
DHCPACK

p19[1]
Refer to the exhibit. An administrator wants to change the name of a brand new switch, using the hostname command as shown. What prompt will display after the command is issued?​
Switch#
My(config)#​
My Switch(config)#​
Switch(config)#​
MySwitch(config)#​

20
After making configuration changes, a network administrator issues a copy running-config startup-config command in a Cisco switch. What is the result of issuing this command?
The configuration changes will be removed and the original configuration will be restored.
The new configuration will be stored in flash memory.
The current IOS file will be replaced with the newly configured file.
The new configuration will be loaded if the switch is restarted.

21
p21[1]
Refer to the exhibit.A TCP segment from a server has been captured by Wireshark, which is running on a host. What acknowledgement number will the host return for the TCP segment that has been received?
2921
250
2
306
21

22
Which technology provides a solution to IPv4 address depletion by allowing multiple devices to share one public IP address?
ARP
DNS
SMB
DHCP
HTTP
NAT

23 What is the purpose of the routing process?
to encapsulate data that is used to communicate across a network
to select the paths that are used to direct traffic to destination networks
to convert a URL name into an IP address
to provide secure Internet file transfer
to forward traffic on the basis of MAC addresses

24 Three bank employees are using the corporate network. The first employee uses a web browser to view a company web page in order to read some announcements. The second employee accesses the corporate database to perform some financial transactions. The third employee participates in an important live audio conference with other corporate managers in branch offices. If QoS is implemented on this network, what will be the priorities from highest to lowest of the different data types?
audio conference, financial transactions, web page
financial transactions, audio conference, web page
audio conference, web page, financial transactions
financial transactions, web page, audio conference

25
A home user is looking for an ISP connection that provides high speed digital transmission over regular phone lines. What ISP connection type should be used?
cell modem
dial-up
cable modem
satellite
DSL

26
Which connection provides a secure CLI session with encryption to a Cisco switch?
a Telnet connection
an SSH connection
a console connection
an AUX connection

27 What is the purpose of the network security accounting function?
to provide challenge and response questions
to require users to prove who they are
to determine which resources a user can access
to keep track of the actions of a user

28
p28[1]
Refer to the exhibit. A network administrator is configuring access control to switch SW1. If the administrator uses Telnet to connect to the switch, which password is needed to access user EXEC mode?
lineconin
linevtyin
letmein
secretin

29
Which publicly available resources describe protocols, processes, and technologies for the Internet but do not give implementation details?
IEEE standards
Request for Comments
IRTF research papers
protocol models

30 A PC is configured to obtain an IP address automatically from network 192.168.1.0/24. The network administrator issues the arp –a command and notices an entry of 192.168.1.255 ff-ff-ff-ff-ff-ff. Which statement describes this entry?
This entry refers to the PC itself.
This entry maps to the default gateway.
This is a static map entry.
This is a dynamic map entry.

31 Which subnet would include the address 192.168.1.96 as a usable host address?
192.168.1.64/26
192.168.1.32/28
192.168.1.32/27
192.168.1.64/29

32
A particular website does not appear to be responding on a Windows 7 computer. What command could the technician use to show any cached DNS entries for this web page?
ipconfig /all
ipconfig /displaydns
arp -a
nslookup

33 Which type of wireless security generates dynamic encryption keys each time a client associates with an AP?
WPA
PSK
WEP
EAP

34
A frame is transmitted from one networking device to another. Why does the receiving device check the FCS field in the frame?
to compare the interface media type between the sending and receiving ends
to determine the physical address of the sending device
to verify that the frame destination matches the MAC address of the receiving device
to check the frame for possible transmission errors
to verify the network layer protocol information

35
p351[1]
Refer to the exhibit. Which IP addressing scheme should be changed?
Site 1
Site 3
Site 4
Site 2

36
What is the effect of configuring the ipv6 unicast-routing command on a router?
to assign the router to the all-nodes multicast group
to permit only unicast packets on the router
to enable the router as an IPv6 router
to prevent the router from joining the all-routers multicast group

37
Which three IP addresses are private ? (Choose three.)
10.1.1.1
172.16.4.4
224.6.6.6
192.168.5.5
172.32.5.2
192.167.10.10

38
p381[1]
Refer to the exhibit. Consider the IP address configuration shown from PC1. What is a description of the default gateway address?
It is the IP address of the Router1 interface that connects the company to the Internet.
It is the IP address of the ISP network device located in the cloud.
It is the IP address of Switch1 that connects PC1 to other devices on the same LAN.
It is the IP address of the Router1 interface that connects the PC1 LAN to Router1.

39 During normal operation, from which location do most Cisco switches and routers run the IOS?
flash
RAM
NVRAM
disk drive

40
What is an important function of the physical layer of the OSI model?
It encodes frames into electrical, optical, or radio wave signals.
It accepts frames from the physical media.
It encapsulates upper layer data into frames.
It defines the media access method performed by the hardware interface.

41
Which procedure is used to reduce the effect of crosstalk in copper cables?
wrapping the bundle of wires with metallic shielding
avoiding sharp bends during installation
requiring proper grounding connections
designing a cable infrastructure to avoid crosstalk interference
twisting opposing circuit wire pairs together

42
What are the three primary functions provided by Layer 2 data encapsulation? (Choose three.)
placement and removal of frames from the media
detection of errors through CRC calculations
conversion of bits into data signals
delimiting groups of bits into frames
data link layer addressing
error correction through a collision detection method
session control using port numbers

43
What method is used to manage contention-based access on a wireless network?
token passing
CSMA/CD
CSMA/CA
priority ordering

44
What happens when part of an Internet radio transmission is not delivered to the destination?
A delivery failure message is sent to the source host.
The part of the radio transmission that was lost is re-sent.
The transmission continues without the missing portion.
The entire transmission is re-sent.

45
What is the auto-MDIX feature on a switch?
the automatic configuration of full-duplex operation over a single Ethernet copper or optical cable
the automatic configuration of an interface for a straight-through or a crossover Ethernet cable connection
the ability to turn a switch interface on or off accordingly if an active connection is detected
the automatic configuration of an interface for 10/100/1000 Mb/s operation

46
Which function is provided by TCP?
detection of missing packets
communication session control
path determination for data packets
data encapsulation

47
How does a Layer 3 switch differ from a Layer 2 switch?
A Layer 3 switch learns the MAC addresses that are associated with each of its ports. However, a Layer 2 switch does not.
A Layer 3 switch maintains an IP address table instead of a MAC address table.
A Layer 3 switch supports VLANs, but a Layer 2 switch does not.
An IP address can be assigned to a physical port of a Layer 3 switch. However, this is not supported in Layer 2 switches.

48
Which two notations are useable nibble boundaries when subnetting in IPv6? (Choose two.)
/68
/62
/66
/64
/70

49
What is the purpose of having a converged network?
to reduce the cost of deploying and maintaining the communication infrastructure
to provide high speed connectivity to all end devices
to make sure that all types of data packets will be treated equally
to achieve fault tolerance and high availability of data network infrastructure devices

50
p50[1]
Refer to the exhibit. A ping to PC3 is issued from PC0, PC1, and PC2 in this exact order. Which MAC addresses will be contained in the S1 MAC address table that is associated with the Fa0/1 port?
just the PC0 MAC address
PC0, PC1, and PC2 MAC addresses
just the PC2 MAC address​
just PC0 and PC1 MAC addresses
just the PC1 MAC address

51
Which field in an IPv4 packet header will typically stay the same during its transmission?
Packet Length
Destination Address
Flag
Time-to-Live

52
What two preconfigured settings that affect security are found on most new wireless routers? (Choose two.)
MAC filtering enabled
default administrator password
WEP encryption enabled
PSK authentication required
broadcast SSID

53
Which parameter does the router use to choose the path to the destination when there are multiple routes available?
the higher metric value that is associated with the destination network
the lower metric value that is associated with the destination network
the higher gateway IP address to get to the destination network
the lower gateway IP address to get to the destination network

54
p54[1]
Refer to the exhibit. What is the significance of the asterisk (*) in the exhibited output?
An asterisk designates that the file system has at least one file that uses that file system.
The asterisk designates which file system is the default file system.
An asterisk indicates that the file system is bootable.
The asterisk shows which file system was used to boot the system.

55
p55[1]

Clipboard013[1]

56
Fill in the blank.
During data communications, a host may need to send a single message to a specific group of destination hosts simultaneously. This message is in the form of a “multicast” message.

57
An administrator uses the Ctrl-Shift-6 key combination on a switch after issuing the ping command. What is the purpose of using these keystrokes?
to interrupt the ping process
to restart the ping process
to allow the user to complete the command
to exit to a different configuration mode

58
p581[1]
Refer to the exhibit. Which area would most likely be an extranet for the company network that is shown?
area A
area D
area C
area B

59
p59[1]

Clipboard014[1]

60
p60[1]

Clipboard0121[1]

61
In which default order will a router search for startup configuration information?
setup mode, NVRAM, TFTP
NVRAM, TFTP, setup mode
NVRAM, RAM, TFTP
TFTP, ROM, NVRAM
flash, ROM, setup mode

62
p62[1]
Launch PT – Hide and Save PT
Open the PT Activity. Perform the tasks in the activity instructions and then answer the question.
Which IPv6 address is assigned to the Serial0/0/0 interface on RT2?
2001:db8:abc:1::1
2001:db8:abc:5::1
2001:db8:abc:5::2
2001:db8:abc:10::15

The result of the tracert command is as follows:
1 11 ms 0 ms 0 ms 2001:db8:abc:1::1
2 4 ms 0 ms 1 ms 2001:db8:abc:5::1
3 11 ms 14 ms 2 ms 2001:db8:abc:10::15
It crosses two routers, so the second line is the IP address for the RT2 serial interface0/0/0.

CCNA 1 Final Exam R&S v5 Exam Answers Introd to Networks, CISCO CCNA 1 Final EXam 2014 Routing and Switching Introduction to Networks

  • choi

    this is quiz answer or final answer ?

  • Blub

    57.
    An administrator uses the Ctrl-Shift-6 key combination on a switch after issuing the ping command. What is the purpose of using these keystrokes?
    to interrupt the ping process
    to restart the ping process
    to allow the user to complete the command
    *to exit to a different configuration mode*

    The answer on this question seems to be incorrect if I may believe 2 other websites, they say the answer should be “To interrupt the ping process”.

  • choi

    this is quiz answer or final answer ?